1. Home
  2. Linux
  3. Split ubuntu between hdd ssd

How To Split Ubuntu Between HDD & SSD

The idea of splitting your Ubuntu installation between two hard drives is a concept that isn’t new. The idea often comes up from those that are looking to spread out one Linux installation onto different hard drives, for many reasons. One of the main reasons users split Ubuntu is to compensate for the small sizes of solid state drives, For example: when you have an SSD and a large 1TB 7200 RPM drive. You want to benefit from the break-neck speeds of an SSD, but you realize it’s small. That’s when you realize that you’ve also got a large second hard drive. With this method, it’s possible to split half of the Linux installation onto the SSD, and the other onto the RPM one.

In this tutorial, we’ll focus on Ubuntu, as the installation tool is the most straight forward, and easiest to understand when it comes to splitting up an installation. That said, the basic concept is easily repeatable on many types of Linux distributions (both complex and beginner ones).

Hard Drives & Solid State Drives

Understand that this method doesn’t require an SSD. It just so happens that SSDs are usually expensive the larger they get. As a result, many Linux users find ways to “expand storage” on their machines. “Splitting up” an installation is the preferred method. Any two hard drives will work with this process, as will a hard drive and a solid state drive.

Note: as SSDs are faster, we’ll use this as /dev/sda. The RPM hard drive should be /dev/sdb.

Preparation

Before installing Ubuntu, get your drives ready for the installation process. Be sure that all of the data on these two hard drives is backed up, as everything on them will have to be deleted. The Ubuntu custom installation tool will format them to create a new file system.

Note: it is possible to mount an existing, in use file system as a second drive, but it’s recommended that you instead start fresh with a new file system for drive health reasons.

With the drives prepared, download Ubuntu. Any Ubuntu version, or flavor will do as the installation tool is what matters here. Once downloaded, go to the Etcher website, and make a live disk. Then, use your PC’s BIOS to load from it.

Installation

As you load up the Ubuntu live disk, a greeting screen appears with two options. Select the option to “Install Ubuntu”. Clicking this option will kick off the pre-setup process. This process involves selecting several options for your new installation. Go through, read, and check the boxes for everything you want in your new installation.

When done, make your way to the “Installation Type” window. In this section, the only option that matters is “Something else”. Select this option, and the “continue” button to be taken to the custom install section.

What follows is the Ubuntu Ubiquity partition tool. In this window, you’ll need to manually assign mount-points for your new installation.

Note: Start off by selecting /dev/sda in the partition layout tool. If there isn’t a file system on it, click “New Partition Table” to create a new one. Do the same with the second drive (/dev/sdb)

BIOS/MBR Instructions

The BIOS/MBR partition layout is very simple, as there is no need for a special boot partition. The first step is to create the “root” drive. Select the free space under /dev/sda, and click + to create a new partition. Multiply 1024 times however many to convert MB to GB.

For example: the entire /dev/sda hard drive is 14 GB. I’d like to make a root partition of 12 GB, so I’d do: 1024 x 12 and get 12288 MB.

Enter your own conversion into the “Size:” area, click “mount point”  and set it to /. Click OK to accept the changes.

Next, create a SWAP partition. Select “free space”, click +, look for “use as” and choose “swap area”.

Note: If you use an SSD, strongly consider skipping the swap partition/file as it contributes to excessive writes.

Lastly, click on  the “free space” section under the /dev/sdb drive, select the + sign and create a new partition. Don’t worry about conversion, as this partition should fill the entire hard drive. Find “mount point”, and select /home.

After all three partitions are set up, click the install button to finish the rest of the Ubuntu installation process.

UEFI/GPT Instructions

The instructions for UEFI Computers is identical to the MBR/BIOS mode with one difference: the boot partition. Before doing anything, select “free space” on /dev/sda and click + to create a new partition. Under size for this partition, enter 512 MB. Then, select find “use as” and select the option “Use as EFI system partition”.

Note: the installer will round 512 MB down to 510 MB. Do not worry! Everything is fine. A lot of times, the Ubuntu installer doesn’t reflect the exact numbers users input.

When the EFI system partition set up in the installer, the hard part is done. From here, go to the instructions above, and follow them.

Lost? Take a look at the picture below. Your EFI partition layout for Ubuntu will be similar.

7 Comments

  1. I don’t understand why the previous comments were so rude, there are plenty of tutorials online for installing Linux, but not for splitting them on two drives. I think you addressed the problem well and offered a well written solution and you provided me with what I needed. Thanks!

  2. Yes you dont discuss the sizes of the partitions, how big should the swap partition be, why would you not have a swap partition and the consequences of not being able to hibernate. how do you parition if you want to preserve your existing home partion data. Think this needs a bit more work for it to be a beginners guide.

    • It is not my responsibility to walk everyone through how large their hard drives should be. Each computer is different. In my tutorial, I used an example. This is a proof of concept.

    • The questions you ask have very nuanced answers which, due to being nuanced, dont lend themselves to a beginner quite. Linux is not a plug n play OS like Windows is. Essentially what people here are asking is “I want to be as knowledgeable as a Senior Linux system administrator but I don’t want to develop the experience, I want Cliff Notes”. It simply does not work that way. There are books on Linux Systems Administration, there are hands on classes. Swap size depends on what you run, the working set size, and your memory size. If you always run V=R you don’t need a swap partition.

  3. Thx for your time putting this together but what I would actually like to see is full (and WORKING) guide to install Ubuntu on ZFS (on HDD, with nice zfs dataset separation for different data types and access patterns) and then when it’s done add L2ARC at SSD. I think it would be much better option.

  4. I think you should consider rewriting this entire article. Keeping in mind that you are leading the public into a step by step and prequalifying it with the idea of 2 hard drives and splitting your installation between the two drives, yet you completely and 100% failed to address the second hard drive, you failed to explain to the reader what drives are being addressed with the partition manager, you failed to gain the confidence of the audience by being specific, accurate and detailed. Most people lose jobs or dont get hired for jobs because they lack strong attention to details. You failed to advise the reader which partition manager label is the SSD and which one is the HDD that you specifically opened your article with. And then you failed to have a summary of what you did.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.